Washer and Dryer Troubleshooting Tips

Signs That Indicate That You Need A Professional To Repair Your Refrigerator

Posted by on 7:52 am in Uncategorized | Comments Off on Signs That Indicate That You Need A Professional To Repair Your Refrigerator

If you want to lower your risk of completely losing all use of your refrigerator, you will need to pay attention to the following signs of trouble. This way, you will know when it is time to call in a professional appliance repair technician. You Are Hearing A Lot Of Clicking Sounds It is not uncommon for your refrigerator to make a few sounds here and there, especially when the compressor kicks on. Of course, you might not notice a lot of noise coming from it during the day because there is generally more noise during the day than there is at night. The noise that you may experience more of during the day includes people and traffic outside, the people in your home, and electronics such as televisions and radios. Therefore, if you are suddenly hearing a lot of noises, such as clicking noises, you are going to want to call a professional. You could have a problem with the compressor and the noise is an indication that it is not kicking on properly. The Door Will Not Stay Shut If you find that you are having a hard time getting the door for your refrigerator to stay shut, you need to take immediate action. This is important because if the refrigerator door is not staying completely shut, air is going to seep into the unit. This warm air can ruin the food that you are trying to keep nice and cold. You could also find that your refrigerator is going to need to start working twice as hard in order to combat all of the warm air that is coming in, which can shorten the life of your appliance and raise your electric bill. After determining that food is not preventing the door from closing, you will want to call in an appliance repair technician to either replace the hinges or door, or simply replace the old rubber seal in order to ensure that the door will properly close. The Freezer Part Is Doing Its Job Too Well Your freezer is supposed to keep the food and drinks within it nice and frozen. However, it is not supposed to accumulate a thick layer of ice all over the inside of the freezer, as it is supposed to automatically defrost itself. If it is not doing that and you are finding that you have to manually defrost it on your own, you will want to call for expert assistance. This way, you will save yourself trouble over the years by not ending up with a lot of freezer burnt food, which is a waste of food and therefore a waste of money. With those three signs of freezer trouble in mind, you should have no trouble knowing when it is time to call in a professional for assistance. Contact a service like All Brand Supply to learn...

read more

Help Your Microwave Last Longer With These Strategies

Posted by on 12:24 pm in Uncategorized | Comments Off on Help Your Microwave Last Longer With These Strategies

If you’re the type of person who has a family that relies on the speed and convenience of the microwave several times per day, the last thing you want to do is find out that it has died prematurely. While you can drop the microwave off at your local appliance repair service to have the problem fixed, it’s also ideal to take some steps that will decrease the likelihood that this vital appliance will suffer a breakdown. Get your family involved in adhering to these steps and you’ll be less likely to suffer the inconvenience of a broken-down microwave. Keep Any Metal Items Out It’s easy enough to inadvertently leave a spoon or fork in the bowl or container that you’re heating in the microwave, but this seemingly innocent slip-up can be detrimental to the lifespan of this appliance. Microwaves and metal objects do not mix — and you’ll likely see a series of sparks shooting around inside the microwave that quickly serve notice of the mistake you’ve made. When the microwave’s heat waves hit your metal utensil, they will bounce off it instead of be absorbed in the same manner as food. With nowhere to go, these excess heat waves can end up actually overheating the microwave and causing serious damage. Watch The Food That You Cook Setting some food to cook in the microwave and then walking away can be detrimental to the lifespan of your appliance. If the food heats more quickly than you anticipated, it will often boil over or even explode. The result can be that the food will clog the small vents located inside the microwave. Over time, a buildup of food blocking these vents can lead to overheating issues and the need to call your local appliance repair service. Instead of setting something that you’re heating up for five minutes, for example, it’s better to set the microwave timer to shorter intervals and stir the food regularly. This will allow the heat in the center to dissipate and prevent an explosion that clogs the vents. Wipe Down Any Messes Right Away Another key tip for prolonging the life of your microwave is to promptly clean any messes that you make. Even if you’re careful about using the microwave, the reality is that you’ll occasionally deal with an explosion. While this is a concern, you can overcome it by immediately getting a damp rag and wiping down the inside of the unit to remove any food residue that could clog the vent upon hardening. To learn more, contact a company like RED’S APPLIANCE...

read more

A Homeowner’s Guide To Installing A New Fridge Gasket

Posted by on 10:25 am in Uncategorized | Comments Off on A Homeowner’s Guide To Installing A New Fridge Gasket

Refrigerators are among the most indispensable appliances in modern life. Unfortunately, a refrigerator with a worn or saggy door gasket can end up driving your energy bill through the roof. The good news is that restoring maximum efficiency is well within your grasp. Read on to learn how to detect a bad door gasket–and how to install a fresh one. Signs of Failure You don’t have to be a trained repair person to recognize the signs of an ailing door gasket. In fact, the two most common symptoms–mold and moisture–are easily detected by the naked eye. Either of these things is a sign that the door is not sealing correctly. As a result, cold air is escaping from the fridge. Where it meets the relatively warmer air from your kitchen, this cold air condenses into moisture, which eventually leads to the growth of unsightly mold. Gasket Removal Once you’ve determined that your door gasket is no longer doing its job correctly, the next step is to get it out of there! If you’re lucky, all this entails is pulling the gasket free from the grooves that lock it into place. Certain fridges, however, utilize special retaining screws to secure the gasket. Loosen these with the appropriately sized hex key and the gasket should easily lift away. Gasket Installation To make installation easier, while removing the old gasket it can help to soak the new gasket in warm water. This acts to increase the pliability of the rubber, which in turn makes it much easier to fit into place. Start off by orienting the gasket in its place at one of the top corners. From there, gradually work your way around the perimeter of the door. Once after the gasket is in place should you tighten any retainer screws. Only tighten them enough that they just grip the rubber. Overtightened screws can actually cause the gasket to warp, thus allowing cold air to escape in places. Now close the door and visually inspect the gasket on all sides. Is it sitting flush against the fridge, forming a nice tight seal? If so, great. If not, you’re going to have to reposition the gasket slightly until it is perfectly centered. Gasket Lubrication In order to promote the tightest and most efficient seal possible, grab a container of petroleum jelly and apply a thin layer to the gasket. This will keep air from escaping beneath microscopic deficiencies in the surface of the rubber. Not only that, but it also gives the gasket a boost in terms of longevity, protecting it from unwanted cracks and other signs of deterioration.  If you need help, contact a service like A OK Appliance...

read more

Three Ways To Reduce Your Air Conditioner Usage To Lower Your Utility Bills

Posted by on 9:29 am in Uncategorized | Comments Off on Three Ways To Reduce Your Air Conditioner Usage To Lower Your Utility Bills

Running your air conditioner through the day and night when it’s hot outside can make the interior of your home a chilly sanctuary, but you’ll feel anything but cool and calm when your next utility bill arrives and is higher than expected. Regular usage of your air conditioner can boost your bill, but it’s possible to adopt different strategies that can limit your air conditioner usage and help you save money. You don’t have to put up with hot, sticky temperatures inside your home, either – these three ideas will keep you cool and help you keep your cool when the bill arrives. Be Smart With Your Thermostat Programming your thermostat in the right way is one of the best methods you can use to reduce your air conditioner usage and save money on your utility bills. Set your thermostat so that your system turns off around the time you leave your home each morning and then turns on again shortly before you’re due to arrive back home. There’s no point in having your home kept chilly when it’s empty. A thermostat is ideal for these settings because you won’t have to try to remember to turn the A/C off before you leave for work and your mind is busy thinking about the workday ahead. Reduce Inefficiencies In Your Home Many homes have inefficient areas in which the inside air is allowed to escape to the outdoors, and vice versa. If hot air can find a way inside your home, it means that your air conditioner will run longer than it should to lower the interior temperature to a comfortable level. You can identify inefficiencies around windows and doors by holding a candle in the area; a flickering flame means the candle is detecting a gust of air. Seal any openings around a window with caulking and replace worn weather stripping around your doors. Enjoy Fresh Air Overnight If the overnight temperature where you live reaches a low level, it can be advantageous to open all the windows on the upper floor of your home to allow the cold air to enter. Doing so will reduce the temperature in your home, which can result in less use of your air conditioner. It’s often ideal to open windows at opposite ends of the upper floor to create a cross-breeze that cools the entire space. Fans placed near the windows can also help to draw cool exterior air inside when it’s not windy outside. For more tips on reducing your air conditioning usage, contact Ron Hammes...

read more

How To Replace The Water Inlet Valve On A Washer

Posted by on 2:25 am in Uncategorized | Comments Off on How To Replace The Water Inlet Valve On A Washer

If your washing machine doesn’t fill or fills slowly, it is time to replace the water inlet valve. The water inlet valve joins the hot and cold water lines from your house to the back of the washer. Here are some tips to replace the washing machine inlet valve. Prepare to Work To make this repair, you need: work gloves Phillips screwdriver bucket camera or labeling tape needle-nose pliers channel lock pliers replacement valve Check your owner’s manual for the specific inlet valve model you need. Unplug the washer, and turn off the water supply, which is usually located on the wall behind the washer, by rotating hot and cold valves to the right If you can’t find them, or there isn’t a shut-off valve, turn off the house’s main water supply. Get someone to help you move the washer away from the wall slightly for easy access to the back. Remove the Old Inlet Valve For easy access, pull the drain hose, a tube secured with a clamp, from the machine, squeezing the ends of the clamp with pliers if needed. Disconnect the access panel on the inlet valve by loosening the screws with the Phillips screwdriver. Pull the panel to the back, then raise it up and off. On some models, you may have to slide a putty knife under the edges of the panel to remove it. Top-load washers will not have hoses connected to the inlet valve, which means you only need to remove wires. Take pictures of the wires and hot and cold supply hoses, or label them with tape. Set buckets under the hoses before you disconnect them to catch water, and remove the hoses with the channel lock pliers. Disconnect the wires from the water inlet valve with the needle-nose pliers. Loosen the mounting screws of the valve with a Phillips screwdriver, lift it out, avoid letting it slip into the cabinet while you remove it, and discard it. Install the New Water Inlet Valve Align the holes of the new valve with the mounting screws, and tighten them with the screwdriver. Using your photo or labels as a guide, reinsert the wires, drain tube, and hoses. Don’t make the connections too tight. Rotate the screwdriver until it stops, then rotate it firmly once to secure the screws. Reinstall the panel, and push clips in place, if needed. Thread the hoses back in place, and secure them with the channel lock pliers. Plug the machine in, and turn on the water. Your washing machine should work properly with a new water inlet valve. If it still doesn’t work, contact a major appliance repair...

read more

Tips For Maintaining Your Refrigerator

Posted by on 5:52 pm in Uncategorized | Comments Off on Tips For Maintaining Your Refrigerator

Keeping your kitchen appliances in top condition helps them last longer and prevents premature repairs. Your refrigerator is no exception to this. The following maintenance tips can help you keep this necessity of the kitchen in peak condition. Tip #1: Keep the Coils Clean The coils on the back of the fridge, called the condenser coils, work constantly to whisk away heat so the fridge can stay cold. Dust, dirt, and animal hair collect on these coils and make it more difficult for them to do their job. Pull the fridge out from the wall and vacuum these coils at least twice a year – more often if you have a shedding pet or another reason for dust to build up quickly on the back of the fridge. Tip #2: Inspect the Gasket Regularly A worn out door gasket results in an air leak, which can put stress on the fridge’s motor since it will have to run more often to keep the fridge cold. Run your fingers around the gasket at least once a month to look for damage, such as tears or loose portions. If the gasket is damaged, remove it and replace it with a new gasket. Attachment methods vary, but typically they are held on with adhesives, screws, or a combination of both. Even if the gasket is in good repair, wipe it down thoroughly with a damp rag to remove any food or soil that could interfere with its seal. Tip #3: Change Out the Filters Refrigerators with built-in ice makers or water dispensers have filters. These usually need to be changed about once a month, but refer to the owner’s manual to be sure for your model. Failure to replace these can cause mineral and debris build-up, which can stress the system. Water dispensers may also have removable spouts or hoses that require monthly cleaning to prevent mineral build-up. Tip #4: Clean it Up Food spills aren’t just unattractive, they can stain or damage the interior of the fridge. Wipe out drawers and shelves weekly, and try to clean up any spills as soon as they happen. Most modern fridges feature frost-free freezers, which mean they defrost automatically. If yours does not, you will need to empty and unplug the fridge if the ice builds up. This will allow the freezer to defrost and work properly. Place a fridge deodorizer or an open box of baking soda in the fridge and freezer after cleaning, and replace it once a month. This will keep odors from penetrating into the interior of the unit. Contact a service like Kaylor Appliance & Refrigeration Service to learn...

read more

Troubleshooting A Clothes Dryer That Has A True Appetite For Your Socks

Posted by on 6:18 am in Uncategorized | Comments Off on Troubleshooting A Clothes Dryer That Has A True Appetite For Your Socks

If you are like most people who are responsible for the laundry in their home, you may crack a joke at some point about your clothes dryer eating the socks, because the mates just seem to disappear somewhere between the wash cycle and folding.  However, if your clothes dryer does seem to truly have a voracious appetite for small laundered clothing articles, you really do have a big problem on your hands. Here are a few signs of a seemingly hungry dryer that is likely in need of appliance repair.  Symptom: Your socks and other small items are literally disappearing in the dryer.  Cause and solution: The drum that tosses your clothing around while drying is supported by at least two wheel bearings. If one of these bearings fails, it allows the drum to slip out of place with the slightest weight–even the weight of a small load of laundry. Your small clothing articles will be tossed right out of the drum and into inner motor housing. It is imperative that you get this issue fixed right away, as loose clothing articles around the heater of your dryer can become a fire hazard.  Symptom: Your clothes come out of the dryer with weird, oily stains and look chewed on.  Cause and Solution: The first time you spot a sock or pair of underwear with weird stains and holes, you may really think that your dryer has somehow grown a set of teeth. You may even have socks that are almost completely swallowed up at the back of the dryer’s drum. However, if you open the dryer door mid-cycle, you will likely see just what is going on.  The holes that you are finding in your clothing are because they are getting stuck between the backside of the rotating drum and the flat back panel of your appliance. The weird oily stains are usually from the grease inside of this tight space. You will need to have a technician come out and replace the support belt of your dryer, as it is likely overextended or broken.  If you feel that your socks are beginning to  feed your clothes dryer, the  chances are that you really need a service technician to take a look at your appliance. If your dryer has been extra hungry lately and your socks are paying the price, contact an appliance repair center like Prompt Appliance Services, Inc. for...

read more

Dishwasher Disasters: Things That Could Damage Your Dishwasher

Posted by on 7:34 am in Uncategorized | Comments Off on Dishwasher Disasters: Things That Could Damage Your Dishwasher

If you’ve just gotten a new dishwasher and want to keep it shiny, new and, above all, operational, you’ll need to be a little careful about the things that you place in it. Too often, people just load their dishwasher with everything they’ve got, turn it on and hope for the best. But the worst that can happen isn’t just some food spots stuck on dishes — it’s actual physical damage to the machine. Small, Lightweight Items Small, lightweight items such as caps and bottle tops should never be casually thrown into the dishwasher. When the water turns on in the dishwasher, these items will get propelled throughout the machine. This could damage your dishes as well as the dishwasher itself. There is usually a place inside of the dishwasher rack where small items can be placed and then contained.  Soft Plastic Bottles Any soft plastics are dangerous, but soft plastic bottles tend to be the most susceptible to this problem. A soft plastic that is not dishwasher safe (it will say if it is on the bottom) will often melt inside of the dishwasher, potentially damaging anything inside. The melting will be worse the closer the bottle is placed to the hot water source inside of the machine. Even hard plastic items, like water bottles, should be placed at the very top of the machine. Melted plastic should always be removed by a professional, like Terry Rickner Appliance Service.​ Hot (Or Very Warm) Items Any items that have just been heated — especially glass and ceramic items — should never be placed in the dishwasher just following. This often happens when a hot item is taken from the oven, emptied and then loaded. Going from one temperature extreme to another can shatter an item. Once shattered, the pieces will usually fall into the food outlet at the bottom of the dishwasher, where it can jam up the machine and the associated pipes. You should always let dishes cool down completely before even putting them in the sink, as this will greatly reduce the risk of shattering.  If you have loaded any of the above items in your dishwasher, don’t fret. An affordable appliance repair center can usually restore your dishwasher to working order, though they may need to order a few parts to replace the ones that were damaged. In general, you should make sure all items are carefully placed and that they are all marked specifically as dishwasher...

read more

Refrigerator Door Switch – Is It Causing Your Problems?

Posted by on 8:21 am in Uncategorized | Comments Off on Refrigerator Door Switch – Is It Causing Your Problems?

Are you having troubles with your refrigerator? One small element that can cause a few different problems is the door switch. Below, you will find a list of the problems that little switch can cause and how to test the switch to determine if it is the culprit. What problems can a bad refrigerator door switch cause? The light doesn’t turn on when you open the door even after replacing the light bulb. The light doesn’t turn off when the door is closed. (Feel the bulb when you open the door – Is it warm?) The temperature inside the refrigerator does not stay below the set temperature. The refrigerator doesn’t stop running. In some cases, the fan doesn’t turn on when the door is opened. (Only applies to units with this feature. Read your owner’s manual to find out if the fan is meant to turn on when you open the door) How do you test the refrigerator door switch? To test the refrigerator door switch you will need: Screwdriver Putty knife Permanent marker Needle-nose pliers Stiff-bristled toothbrush Multi-tester Note: Before you begin working on the refrigerator, unplug it or shut off the breaker to the outlet. Working on this element with power going to the refrigerator could lead to electrical shock. Remove the Switch Locate the switch and look for any screws that could be holding it in place. Some switches are held in by screws, while others just snap into place. If you see screws, remove them carefully so that you don’t strip them. If there aren’t any screws, or after you have removed them, slide the putty knife behind the outer edge of the switch to pry it out of place. Be gentle because this switch is connected to wires that could break if you are too forceful. Prepare for Testing To test the switch, you must disconnect the wires from it. Before you do, label each wire and the connection that they are connected to. For example, draw two lines on the wire and two lines on the connector that it is attached to. On the other wire and connection, draw one line. This will help you reconnect everything the right way when you have completed your test. Once you have labeled the wires and connectors, use needle nose pliers to gently grab the connectors and pull them off of the switch. Use a stiff-bristled toothbrush to clean the connectors on the switch. This will remove any corrosion or dirt that could prevent a good current. Test the Switch Set your multi-tester to X1 ohms setting. Place each probe on each terminal. The tester should give you an infinity to zero reading. Now, keeping the probes in place, depress the switch. The tester should now display a reading of infinity. If the switch fails these tests, replace it with a new switch. If you are unable to complete this test yourself or you complete it and the switch wasn’t the cause of your problems, contact an appliance repair technician like Anderson’s Appliance Repair Service for...

read more

3 Ways To Know It’s Time For Refrigerator Repairs

Posted by on 4:25 am in Uncategorized | 0 comments

Could you imagine life without a refrigerator? Probably not. You would have to find other unconventional ways to keep your fruits, vegetables, meats, and other foods in the right temperature to guarantee that they won’t go bad. Since you rely so much on your refrigerator to do this for you, you want to be sure that you keep the fridge in the best working condition. To do this, you should know some signs that point to your refrigerator needing repairs. Here are three sure ways to know that it’s time for these repairs: Food is Freezing: If the food that is not in the freezer begins to freeze, then there is a problem with your refrigerator. This problem is called over-cooling and is largely due to the fact that the control of the compressor has gone bad. There are a couple things you will want to check that will help determine what has made the control of the compressor go bad in the first place. First off, be sure that the thermostat in the fridge isn’t set at too low of a temperature, and then check that the coils in the fridge haven’t iced over. These two things you can fix on your own by defrosting the coils and changing the temperature on the thermostat. If the problem extends beyond this, then you need a professional appliance service like A Pittsburgh Service Center to come in. There’s a Leak: A leak in the refrigerator is a repair that needs to be resolved right away. This is because the water that is leaking can cause damages to the counters and flooring in your kitchen, which will lead to further costly repairs you will have to make. There are a few things that could have caused the leak in your fridge, such as a crack in the drain pan or a loose water line connection. Either way, you are going to need professionals to check it out for you and make the repairs.  Refrigerator Door is Leaking Cold Air: You don’t want the refrigerator door to allow cold air to leak when it is closed. This works up energy costs significantly and guarantees that the food inside of your fridge probably isn’t staying cool enough. A refrigerator door that doesn’t trap cold air inside is probably due to a poor door seal. You will want to have a professional appliance service make their way to your home to replace this seal. They will fit the right size seal for your specific fridge to ensure that cold air is contained.  Knowing these three sure signs of refrigerator repairs will allow you to know that you need to fix the problem before it becomes worse. It also ensures that you know when you need simple repairs rather than a full refrigerator...

read more